SANE
| Download Backend Source: | ftp://ftp.sane-project.org/pub/sane/sane-backends-1.0.21/sane-backends-1.0.21.tar.gz |
|---|---|
| Download Frontend Source: | ftp://ftp.sane-project.org/pub/sane/sane-frontends-1.0.14/sane-frontends-1.0.14.tar.gz |
| Download Frontend Patch: | http://svn.cross-lfs.org/svn/repos/patches/sane-frontends/sane-frontends-1.0.14-SANCAP-1.patch |
Contents
Introduction to SANE
SANE is short for Scanner Access Now Easy. Scanner access, however, is far from easy, since every vendor has their own protocols. The only known protocol that should bring some unity into this chaos is the TWAIN interface, but this is too imprecise to allow a stable scanning framework. Therefore, SANE comes with its own protocol, and the vendor drivers can't be used.
SANE is split into back ends and front ends. The back ends are drivers for the supported scanners and cameras. The front ends are user interfaces to access the backends.
Project Homepage: http://www.sane-project.org/
Dependencies
Optional (BackEnd)
Optional (FrontEnd)
Non-Multilib
Backend
Compile the package:
./configure --prefix=/usr --sysconfdir=/etc \
--localstatedir=/var &&
make
Install the package:
make install
Frontend
Compile the package:
patch -Np1 -i ../sane-frontends-1.0.14-SANCAP-1.patch ./configure --prefix=/usr && make
Install the package:
make install &&
install -v -m644 doc/sane.png xscanimage-icon-48x48-2.png \
/usr/share/sane
If GIMP is installed and you would like to use xscanimage as a scanning plugin, run the following command:
ln -v -s ../../../../bin/xscanimage /usr/lib/gimp/2.0/plug-ins
Multilib
32Bit
Backend
Compile the package:
CC="gcc ${BUILD32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" USE_ARCH=32 \
./configure --prefix=/usr --sysconfdir=/etc \
--localstatedir=/var &&
make
Install the package:
make install &&
mv -v /usr/bin/sane-config{,-32}
Frontend
Compile the package:
patch -Np1 -i ../sane-frontends-1.0.14-SANCAP-1.patch
CC="gcc ${BUILD32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" USE_ARCH=32 \
./configure --prefix=/usr &&
make
Install the package:
make install
If GIMP is installed and you would like to use xscanimage as a scanning plugin, run the following command:
ln -v -s ../../../../bin/xscanimage /usr/lib/gimp/2.0/plug-ins
N32
Backend
Compile the package:
CC="gcc ${BUILDN32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" USE_ARCH=n32 \
./configure --prefix=/usr --sysconfdir=/etc --libdir=/usr/lib32 \
--localstatedir=/var &&
make
Install the package:
make install &&
mv -v /usr/bin/sane-config{,-n32}
Frontend
Compile the package:
patch -Np1 -i ../sane-frontends-1.0.14-SANCAP-1.patch
CC="gcc ${BUILDN32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" USE_ARCH=n32 \
./configure --prefix=/usr --libdir=/usr/lib32 &&
make
Install the package:
make install
If GIMP is installed and you would like to use xscanimage as a scanning plugin, run the following command:
ln -v -s ../../../../bin/xscanimage /usr/lib32/gimp/2.0/plug-ins
64Bit
Backend
Compile the package:
CC="gcc ${BUILD64}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" USE_ARCH=64 \
./configure --prefix=/usr --sysconfdir=/etc --libdir=/usr/lib64 \
--localstatedir=/var &&
make
Install the package:
make install &&
mv -v /usr/bin/sane-config{,-64} &&
ln -sfv multiarch_wrapper /usr/bin/sane-config
Frontend
Compile the package:
patch -Np1 -i ../sane-frontends-1.0.14-SANCAP-1.patch
CC="gcc ${BUILD64}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" USE_ARCH=64 \
./configure --prefix=/usr --libdir=/usr/lib64 &&
make
Install the package:
make install &&
install -v -m644 doc/sane.png xscanimage-icon-48x48-2.png \
/usr/share/sane
If GIMP is installed and you would like to use xscanimage as a scanning plugin, run the following command:
ln -v -s ../../../../bin/xscanimage /usr/lib64/gimp/2.0/plug-ins
