Difference between revisions of "Acpid"
m |
|||
| Line 15: | Line 15: | ||
Compile the package: | Compile the package: | ||
| − | |||
sed -i "s/-Werror//g" Makefile && | sed -i "s/-Werror//g" Makefile && | ||
make | make | ||
| Line 30: | Line 29: | ||
Compile the package: | Compile the package: | ||
| − | |||
sed -i "s/-Werror//g" Makefile && | sed -i "s/-Werror//g" Makefile && | ||
make CC="gcc ${BUILD32}" | make CC="gcc ${BUILD32}" | ||
| Line 42: | Line 40: | ||
Compile the package: | Compile the package: | ||
| − | |||
sed -i "s/-Werror//g" Makefile && | sed -i "s/-Werror//g" Makefile && | ||
make CC="gcc ${BUILDN32}" | make CC="gcc ${BUILDN32}" | ||
| Line 54: | Line 51: | ||
Compile the package: | Compile the package: | ||
| − | |||
sed -i "s/-Werror//g" Makefile && | sed -i "s/-Werror//g" Makefile && | ||
make CC="gcc ${BUILD64}" | make CC="gcc ${BUILD64}" | ||
| Line 136: | Line 132: | ||
| None | | None | ||
|} | |} | ||
| + | |||
| + | [[Category:General Libs]] | ||
Revision as of 00:07, 19 March 2009
| Download Source: | http://prdownloads.sourceforge.net/acpid/acpid-1.0.10.tar.gz |
|---|
Contents
Introduction to Acpid
The Advanced Configuration & Power Interface Daemon (ACPID) is a flexible and totally extensible daemon for responding to ACPI events. It listens to /proc/acpi/event and executes programs to handle the events when they occur. The programs it executes are configured through a set of configuration files.
Project Homepage: https://sourceforge.net/projects/acpid/
Dependencies
Non-Multilib
Compile the package:
sed -i "s/-Werror//g" Makefile && make
Install the package
make install
Multilib
This package does not provide any libraries so only one installation is needed.
32Bit
Compile the package:
sed -i "s/-Werror//g" Makefile &&
make CC="gcc ${BUILD32}"
Install the package
make install
N32
Compile the package:
sed -i "s/-Werror//g" Makefile &&
make CC="gcc ${BUILDN32}"
Install the package
make install
64Bit
Compile the package:
sed -i "s/-Werror//g" Makefile &&
make CC="gcc ${BUILD64}"
Install the package
make install
Configuring
Configuring Events
The following sample event included with Acpid will set the hard drive to spindown after 5 minutes when the computer is on battery power but keep it on 100% of the time while the computer is plugged in:
mkdir -pv /etc/acpi/events && cp -v samples/battery/battery.conf /etc/acpi/events && cp -v samples/battery/battery.sh /etc/acpi && chmod 755 /etc/acpi/battery.sh
The above sample depends on Hdparm to function properly.
Bootscript
Create the bootscript:
cat > /etc/rc.d/init.d/acpid << "EOF"
#!/bin/sh
# Begin $rc_base/init.d/acpid
. /etc/sysconfig/rc
. ${rc_functions}
case "${1}" in
start)
boot_mesg "Starting acpid..."
loadproc /usr/sbin/acpid
;;
stop)
boot_mesg "Stopping acpid..."
killproc /usr/sbin/acpid
;;
restart)
${0} stop
sleep 1
${0} start
;;
status)
statusproc /usr/sbin/acpid
;;
*)
echo "Usage: ${0} {start|stop|restart|status}"
exit 1
;;
esac
# End $rc_base/init.d/acpid
EOF
chmod -v 754 /etc/rc.d/init.d/acpid
Link it into the runlevels:
for link in /etc/rc.d/rc{{0,1,6}.d/K32,{2,3,4,5}.d/S18}acpid; do
ln -sfv ../init.d/acpid $link;
done
Contents
| Installed Programs: | acpid acpi_listen |
|---|---|
| Installed Libraries: | None |
| Installed Directories: | None |
