Difference between revisions of "Hdparm"
From CBLFS
Jump to navigationJump to search (I added the "Contents" section.) |
|||
| (7 intermediate revisions by 4 users not shown) | |||
| Line 2: | Line 2: | ||
|-valign="top" | |-valign="top" | ||
!Download Source: | !Download Source: | ||
| − | | http://prdownloads.sourceforge.net/hdparm/hdparm- | + | | http://prdownloads.sourceforge.net/hdparm/hdparm-{{Hdparm-Version}}.tar.gz |
|} | |} | ||
---- | ---- | ||
| − | + | {{Package-Introduction|hdparm - get/set ATA/SATA drive parameters under Linux|http://hdparm.sourceforge.net/}} | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Dependencies == | == Dependencies == | ||
| Line 33: | Line 26: | ||
=== 32Bit === | === 32Bit === | ||
| − | + | Compile the package: | |
| + | |||
| + | make CC="gcc ${BUILD32}" | ||
| + | |||
| + | Install the package | ||
| + | |||
| + | make install | ||
=== N32 === | === N32 === | ||
| − | + | Compile the package: | |
| + | |||
| + | make CC="gcc ${BUILDN32}" | ||
| + | |||
| + | Install the package | ||
| + | |||
| + | make install | ||
=== 64Bit === | === 64Bit === | ||
| Line 43: | Line 48: | ||
Compile the package: | Compile the package: | ||
| − | make | + | make CC="gcc ${BUILD64}" |
Install the package | Install the package | ||
| Line 54: | Line 59: | ||
|-valign="top" | |-valign="top" | ||
! Installed Programs: | ! Installed Programs: | ||
| − | | | + | | /sbin/hdparm |
|-valign="top" | |-valign="top" | ||
! Installed Libraries: | ! Installed Libraries: | ||
| Line 70: | Line 75: | ||
| provides a command-line interface to various hard disk ioctls supported by the stock Linux ATA/IDE device driver subsystem. | | provides a command-line interface to various hard disk ioctls supported by the stock Linux ATA/IDE device driver subsystem. | ||
|} | |} | ||
| + | |||
| + | [[Category:General Utilities]] | ||
Latest revision as of 03:18, 6 February 2011
| Download Source: | http://prdownloads.sourceforge.net/hdparm/hdparm-9.37.tar.gz |
|---|
Contents
Introduction to Hdparm
hdparm - get/set ATA/SATA drive parameters under Linux
Project Homepage: http://hdparm.sourceforge.net/
Dependencies
Non-Multilib
Compile the package:
make
Install the package
make install
Multilib
This package does not provide any libraries so only one installation is needed.
32Bit
Compile the package:
make CC="gcc ${BUILD32}"
Install the package
make install
N32
Compile the package:
make CC="gcc ${BUILDN32}"
Install the package
make install
64Bit
Compile the package:
make CC="gcc ${BUILD64}"
Install the package
make install
Contents
| Installed Programs: | /sbin/hdparm |
|---|---|
| Installed Libraries: | ??? |
| Installed Directories: | ??? |
Short Descriptions
| hdparm | provides a command-line interface to various hard disk ioctls supported by the stock Linux ATA/IDE device driver subsystem. |
|---|
