Difference between revisions of "Ifplugd"
(→Bootscript) |
|||
Line 115: | Line 115: | ||
Also, if you want to pass '''ifplugd''' parameters other than the defaults, you need to set ARGS (also within ifplugd.conf) to the parameters that you actually want. However, the defaults are probably sufficient. | Also, if you want to pass '''ifplugd''' parameters other than the defaults, you need to set ARGS (also within ifplugd.conf) to the parameters that you actually want. However, the defaults are probably sufficient. | ||
− | Remove unnecessary links from the | + | Remove unnecessary links from the [[bootscripts]]: |
rm -v /etc/rc.d/*/K80network | rm -v /etc/rc.d/*/K80network |
Revision as of 19:13, 17 October 2007
Download Source: | http://0pointer.de/lennart/projects/ifplugd/ifplugd-0.28.tar.gz |
---|
Contents
Introduction to Ifplugd
ifplugd is a Linux daemon which will automatically configure your ethernet device when a cable is plugged in and automatically unconfigure it if the cable is pulled. This is useful on laptops with onboard network adapters, since it will only configure the interface when a cable is really connected.
With the clfs-bootscripts, you will get an ethernet connection if the cable is connected when you boot, but otherwise will not - even if you connect the cable later. With ifplugd, you will have a connection whenever the cable is connected - regardless of whether it was connected on boot or how many times you unplug and plug it back in after booting. ifplugd also works with wireless devices.
Project Homepage: http://0pointer.de/lennart/projects/ifplugd/
Dependencies
Required
Optional
- xmltoman (for rebuilding the man pages)
- Subversion (for rebuilding svn-release.h)
- Lynx (for regenerating the README)
Additional Configuration Options
If you don't have Lynx installed, pass the following flag to configure:
--disable-lynx
If you don't have xmltoman installed, pass the following flag to configure:
--disable-xmltoman
If you don't have Subversion installed, pass the following flag to configure:
--disable-subversion
Nothing bad happens if you don't have one of the optional packages and you forget to pass the disabling flag, but configure will complain with a warning.
Non-Multilib
Compile the package:
./configure --prefix=/usr --sysconfdir=/etc \ --sbindir=/sbin make
Install the package:
make install
Command Explanations
--sysconfdir=/etc: We use this flag because the default is /usr/etc which you probably don't want to happen.
--sbindir=/sbin: We use this flag because the default is /usr/sbin and you may want ifplugd to be available even when /usr is on another partition.
rm -v ....: The ifplugd script effectively replaces clfs-bootscripts' network script, so we need to remove the network script (or at least its links in /etc/rc.d/rcX.d) so that they won't try to run.
ln -sv ....: We need to have links in the /etc/rc.d/rcX.d directories in order for ifplugd to run.
sed -i ....: ifplugd.action points to /sbin for the ifdown and ifup scripts, but on clfs systems, they reside in /etc/sysconfig/network-devices, so we need to redirect it.
Multilib
This package does not provide any libraries so only one installation is needed.
32Bit
Compile the package:
PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" CC="gcc ${BUILD32}" \ ./configure --prefix=/usr --sysconfdir=/etc \ --sbindir=/sbin && make
Install the package:
make install
N32
Compile the package:
PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" CC="gcc ${BUILDN32}" \ ./configure --prefix=/usr --sysconfdir=/etc \ --sbindir=/sbin && make
Install the package:
make install
64Bit
Compile the package:
PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" CC="gcc ${BUILS64}" \ ./configure --prefix=/usr --sysconfdir=/etc \ --sbindir=/sbin && make
Install the package:
make install
Configuring ifplugd
Configuration File
/etc/ifplugd/ifplugd.conf
Bootscript
In ifplugd.conf, set INTERFACES to the network interfaces that you have on your computer (e.g. eth0).
Also, if you want to pass ifplugd parameters other than the defaults, you need to set ARGS (also within ifplugd.conf) to the parameters that you actually want. However, the defaults are probably sufficient.
Remove unnecessary links from the bootscripts:
rm -v /etc/rc.d/*/K80network rm -v /etc/rc.d/*/S20network
If you want, you can remove the network bootscript, but if you decide you want it, you'll have to reinstall it from the clfs-bootscripts package.
rm -v /etc/rc.d/init.d/network
Create the links necessary to have ifplugd actually run:
ln -sv ../init.d/ifplugd /etc/rc.d/rc1.d/K80ifplugd ln -sv ../init.d/ifplugd /etc/rc.d/rc2.d/S20ifplugd ln -sv ../init.d/ifplugd /etc/rc.d/rc3.d/S20ifplugd ln -sv ../init.d/ifplugd /etc/rc.d/rc4.d/S20ifplugd ln -sv ../init.d/ifplugd /etc/rc.d/rc5.d/S20ifplugd ln -sv ../init.d/ifplugd /etc/rc.d/rc6.d/K80ifplugd
Alter /etc/ifplugd/ifplugd.action so that it points to the correct location for the ifdown and ifup scripts:
sed -i 's@/sbin/@/etc/sysconfig/network-devices/@g' /etc/ifplugd/ifplugd.action
Contents
Installed Programs: | ifplugd, ifplugstatus |
---|---|
Installed Libraries: | None |
Installed Scripts: | ifplugd |
Installed Directory: | /etc/ifplugd |
Short Descriptions
ifplugd | is a daemon which will automatically configure your ethernet device when a cable is plugged in and automatically unconfigure it if the cable is pulled. |
---|---|
ifplugstatus | is an utility which may be used to detect the link status of a local Linux ethernet device. |