Difference between revisions of "Ivtv"
Weibullguy (talk | contribs) (→Dependencies) |
Weibullguy (talk | contribs) (Version template) |
||
| Line 2: | Line 2: | ||
|-valign="top" | |-valign="top" | ||
!Download Source: | !Download Source: | ||
| − | | http://dl.ivtvdriver.org/ivtv/stable/ivtv- | + | | http://dl.ivtvdriver.org/ivtv/stable/ivtv-{{Ivtv-Version}}.tar.gz |
|} | |} | ||
| Line 34: | Line 34: | ||
== Multilib == | == Multilib == | ||
| + | |||
| + | The instructions for multilib build are dependent upon the version of CLFS you used to build your base system. If you used the stable version (1.0.0), then the kernel Makefile wasn't adjusted to install kernel modules in /lib64. This was changed in the developmental version. | ||
| + | |||
| + | === Using Stable CLFS Release === | ||
| + | |||
| + | Compile the Package: | ||
| + | |||
| + | make KDIR="/lib/modules/$(uname -r)/build" PREFIX="/usr" | ||
| + | |||
| + | Install the package: | ||
| + | |||
| + | make KDIR="/lib/modules/$(uname -r)/build" PREFIX="/usr" install | ||
| + | |||
| + | If you would like to load the module now, run the following command: | ||
| + | |||
| + | modprobe ivtv | ||
| + | |||
| + | === Using Development CLFS Release === | ||
Compile the Package: | Compile the Package: | ||
Revision as of 08:39, 23 June 2007
| Download Source: | http://dl.ivtvdriver.org/ivtv/stable/ivtv-1.4.0.tar.gz |
|---|
Contents
Introduction to Ivtv
The IVTV project develops a kernel driver for Linux and a driver for X11 for hardware based on Conexant's CX23415/CX23416 codec chip such as the Hauppauge PVR 150/250/350/500 models and other supported hardware.
Project Homepage: http://ivtvdriver.org/index.php/Main_Page
Dependencies
Required
Support for your video capture card must be compiled into the kernel or as a kernel module. These configuration options can be found under
Device Driver ---> Multimedia devices ---> Video Capture Adapters
It is recommended that the "Autoselect pertinent encoders/decoders and other helper chips" option be disabled and that you select the appropriate device(s) under the newly revealed menu "Encoders/decoders and other helper chips"
Non-Multilib
Compile the Pakcage:
make
Install the package:
make install
If you would like to load the module now, run the following command:
modprobe ivtv
Multilib
The instructions for multilib build are dependent upon the version of CLFS you used to build your base system. If you used the stable version (1.0.0), then the kernel Makefile wasn't adjusted to install kernel modules in /lib64. This was changed in the developmental version.
Using Stable CLFS Release
Compile the Package:
make KDIR="/lib/modules/$(uname -r)/build" PREFIX="/usr"
Install the package:
make KDIR="/lib/modules/$(uname -r)/build" PREFIX="/usr" install
If you would like to load the module now, run the following command:
modprobe ivtv
Using Development CLFS Release
Compile the Package:
make KDIR="/lib64/modules/$(uname -r)/build" PREFIX="/usr"
Install the package:
make KDIR="/lib64/modules/$(uname -r)/build" PREFIX="/usr" install
If you would like to load the module now, run the following command:
modprobe ivtv
