HAL

Download Source:	http://people.freedesktop.org/~david/dist/hal-0.5.14.tar.gz

---

Introduction to HAL

HAL is a hardware abstraction layer and aims to provide a live list of devices present in the system at any point in time. HAL tries to understand both physical devices (such as PCI, USB) and the device classes (such as input, net and block) physical devices have, and it allows merging of information from so called device info files specific to a device.

HAL provides a network API through D-BUS for querying devices and notifying when things change. Finally, HAL provides some monitoring (in an unintrusive way) of devices, presently ethernet link detection and volume mounts are monitored.

Project Homepage: http://www.freedesktop.org/Software/hal/

Dependencies

As of hal-0.5.8 libvolume_id.so (From Udev) is a required dependency. On multilib systems you must have more then one copy of this library, (32bit,64bit,N32). Please refer to the clfs-svn book for information on configuring a multilib udev. WARNING: Installing a newer or older version of udev then what is currently installed on your system can cause problems booting because of the frequent changes in the rules format. Please use the same version you currently have, or make the appropriate changes/upgrades to your rule set.

Note

HAL-0.5.9.1 incompatible with PolicyKit-0.3 by some API changes. You must explicitly enable PolicyKit support for HAL-0.5.9.1. Either use the development version of HAL from freedesktop's GIT to build against PolicyKit-0.3 or do not pass the --enable-policykit flag to the configure script.

Getting the latest source

Note

This section is optional but recommended. You need this command only if you want to build the latest development version. Be advised that the latest development version is looking for a newer libvolume_id than you may have on your system. Refer to the Udev warning above before upgrading.

Check out the source from freedesktop.org:

git clone git://anongit.freedesktop.org/git/hal &&
cd hal &&
git-checkout -b 4141c63d453885204a45bdd4b968d19e2007b779 &&
cd ..

It couldn't hurt to make a tarball so you have an unmodified source around for the future:

tar cvjf hal{-$(date +%Y%m%d).tar.bz2,}

Note

Replace "./configure" with "./autogen.sh" to build the latest development version.

Dependencies

Required

• D-BUS Glib
• Glib2
• Python
• Perl_Module_XML::Parser

Recommended

• hal-info
• PCI Utilities
• usbutils

Optional

• Parted
• dmidecode
• Acpid
• Expat
• libusb
• Doxygen
• DocBook Utils
• intltool
• Gtk-Doc
• PolicyKit
• pm-utils
• GIT (to get the source)

HalDaemon User/Group

groupadd -g 19 haldaemon &&
useradd -c "HAL Daemon User" -d /dev/null \
        -u 19 -g haldaemon -s /bin/false haldaemon

Configuration Information

The following are some options you may wish to pass to HAL:

--enable-parted use Parted

--enable-policy-kit use PolicyKit

--enable-console-kit use ConsoleKit

--enable-acl-management use ACL management

--enable-umount-helper provide umount.hal helper

Non-Multilib

Compile the package:

./configure --prefix=/usr --sysconfdir=/etc \
    --libexecdir=/usr/lib/hal --localstatedir=/var &&
make

Install the package

make install &&
install -v -m755 -d /var/run/hald

Command Explanations

--libexecdir=/usr/lib/hal: This parameter forces the installation of libexec files to /usr/lib/hal instead of /usr/libexec.

--localstatedir=/var: This parameter forces the creation of the pid file to /var/run/hald instead of /usr/var/run/hald.

Multilib

32Bit

Compile the package:

export USE_ARCH=32 &&
CC="gcc ${BUILD32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" \
./configure --prefix=/usr --sysconfdir=/etc \
    --libexecdir=/usr/lib/hal --localstatedir=/var &&
make

Install the package

make install &&
unset USE_ARCH

N32

export USE_ARCH=n32 &&
CC="gcc ${BUILDN32}" PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" \
./configure --prefix=/usr --sysconfdir=/etc --libdir=/usr/lib32 \
    --libexecdir=/usr/lib/hal --localstatedir=/var &&
make

Install the package

make install &&
unset USE_ARCH

64Bit

export USE_ARCH=64 &&
CC="gcc ${BUILD64}" PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" \
./configure --prefix=/usr --sysconfdir=/etc --libdir=/usr/lib64 \
    --libexecdir=/usr/lib/hal --localstatedir=/var &&
make

Install the package

make install &&
unset USE_ARCH &&
install -v -m755 -d /var/run/hald

Configuration

Bootscript

Install the bootscript from the blfs-bootscripts package with the following command:

make install-haldaemon

Contents

Installed Programs:	hal-device, hal-device-manager, hal-find-by-capability, hal-find-by-property, hal-get-property, hal-set-property, hald and lshal
Installed Libraries:	libhal.{so,a} and libhal-storage,{so,a}
Installed Directories:	/etc/hal, /usr/include/hal, /usr/lib/hal, /usr/share/doc/hal-0.5.14, /usr/share/hal and /var/run/hald

Short Descriptions

hal-device	is used to create, remove or show a HAL device.
hal-device-manager	shows a graphical representation of all the devices HAL is aware of. This program requires GNOME-Python. Here is a screenshot of hal-device-manager communicating with the HAL daemon and displaying a tree of device objects. The shown properties in the screenshot are for a device object representing a hard disk.
hal-find-by-capability	prints the Unique Device Identifiers for HAL device objects of a given capability.
hal-find-by-property	prints the Unique Device Identifiers for HAL device objects where a given property assumes a given value.
hal-get-property	retrieves a property from a device.
hal-set-property	attempts to set property for a device. Note that, due to security considerations, it may not be possible to set a property.
hald	is the HAL daemon program.
lshal	shows all devices and their properties. If the --monitor option is given then the device list and all devices are monitored for changes.
libhal.{so,a}	contains the API functions required by the HAL programs.
libhal-storage.{so,a}	contains the API functions required by the HAL storage and volume utility programs.