Difference between revisions of "ALSA Tools"
From CBLFS
Jump to navigationJump to searchm |
|||
| (13 intermediate revisions by 4 users not shown) | |||
| Line 2: | Line 2: | ||
|- | |- | ||
!Download Source: | !Download Source: | ||
| − | | ftp://ftp.alsa-project.org/pub/tools/alsa-tools- | + | | ftp://ftp.alsa-project.org/pub/tools/alsa-tools-{{ALSA Tools-Version}}.tar.bz2 |
|} | |} | ||
| − | - | + | {{Package-Introduction|The ALSA Tools package contains various advanced tools for use with certain sound cards. |
| − | + | This package is only needed if you have advanced requirements for your sound card. A list of the various tools can be found at http://alsa.opensrc.org/Alsa-tools.|http://www.alsa-project.org/}} | |
| + | |||
| + | {{Note|You don't compile the tools all at once, but instead build them individually. For each tool that you wish to build, you go into its directory and run the build commands from there.}} | ||
== Dependencies == | == Dependencies == | ||
| Line 16: | Line 18: | ||
* [[Gtk1]] (To Build echomixer, envy24control, and rmedigicontrol) | * [[Gtk1]] (To Build echomixer, envy24control, and rmedigicontrol) | ||
* [[FLTK]] (To Build hdspconf and hdspmixer) | * [[FLTK]] (To Build hdspconf and hdspmixer) | ||
| − | * [[ | + | * [[Qt3]] (To Build qlo10k1) |
| + | |||
| + | {{Note|'''ld10k1''' must be built before '''qt10k1'''}} | ||
== Non-Multilib == | == Non-Multilib == | ||
| − | Compile | + | Compile each package with: |
./configure --prefix=/usr && | ./configure --prefix=/usr && | ||
make | make | ||
| − | Install | + | Install each package with: |
make install | make install | ||
| Line 33: | Line 37: | ||
=== 32Bit === | === 32Bit === | ||
| − | Compile | + | Compile each package with: |
CC="gcc ${BUILD32}" CXX="g++ ${BUILD32}" USE_ARCH=32 PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" \ | CC="gcc ${BUILD32}" CXX="g++ ${BUILD32}" USE_ARCH=32 PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" \ | ||
| Line 39: | Line 43: | ||
make | make | ||
| − | Install | + | Install each package with: |
make install | make install | ||
| Line 45: | Line 49: | ||
=== N32 === | === N32 === | ||
| − | Compile | + | Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: |
| + | |||
| + | sed -i "s@QTDIR/lib@&32@g" configure | ||
| + | |||
| + | Compile each package with: | ||
CC="gcc ${BUILDN32}" CXX="g++ ${BUILDN32}" USE_ARCH=n32 PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" \ | CC="gcc ${BUILDN32}" CXX="g++ ${BUILDN32}" USE_ARCH=n32 PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" \ | ||
| Line 51: | Line 59: | ||
make | make | ||
| − | Install | + | Install each package with: |
make install | make install | ||
| Line 57: | Line 65: | ||
=== 64Bit === | === 64Bit === | ||
| − | Compile | + | Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: |
| + | |||
| + | sed -i "s@QTDIR/lib@&64@g" configure | ||
| + | |||
| + | Compile each package with: | ||
CC="gcc ${BUILD64}" CXX="g++ ${BUILD64}" USE_ARCH=64 PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" \ | CC="gcc ${BUILD64}" CXX="g++ ${BUILD64}" USE_ARCH=64 PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" \ | ||
| Line 63: | Line 75: | ||
make | make | ||
| − | Install | + | Install each package with: |
make install | make install | ||
Latest revision as of 10:03, 16 October 2007
| Download Source: | ftp://ftp.alsa-project.org/pub/tools/alsa-tools-1.0.23.tar.bz2 |
|---|
Contents
Introduction to ALSA Tools
The ALSA Tools package contains various advanced tools for use with certain sound cards.
This package is only needed if you have advanced requirements for your sound card. A list of the various tools can be found at http://alsa.opensrc.org/Alsa-tools.
Project Homepage: http://www.alsa-project.org/
Note
You don't compile the tools all at once, but instead build them individually. For each tool that you wish to build, you go into its directory and run the build commands from there.
Dependencies
Required
Optional
- Gtk1 (To Build echomixer, envy24control, and rmedigicontrol)
- FLTK (To Build hdspconf and hdspmixer)
- Qt3 (To Build qlo10k1)
Note
ld10k1 must be built before qt10k1
Non-Multilib
Compile each package with:
./configure --prefix=/usr && make
Install each package with:
make install
Multilib
32Bit
Compile each package with:
CC="gcc ${BUILD32}" CXX="g++ ${BUILD32}" USE_ARCH=32 PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" \
./configure --prefix=/usr &&
make
Install each package with:
make install
N32
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries:
sed -i "s@QTDIR/lib@&32@g" configure
Compile each package with:
CC="gcc ${BUILDN32}" CXX="g++ ${BUILDN32}" USE_ARCH=n32 PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" \
./configure --prefix=/usr --libdir=/usr/lib32 &&
make
Install each package with:
make install
64Bit
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries:
sed -i "s@QTDIR/lib@&64@g" configure
Compile each package with:
CC="gcc ${BUILD64}" CXX="g++ ${BUILD64}" USE_ARCH=64 PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" \
./configure --prefix=/usr --libdir=/usr/lib64 &&
make
Install each package with:
make install
