Difference between revisions of "ALSA Tools"
From CBLFS
Jump to navigationJump to searchm |
|||
| Line 3: | Line 3: | ||
!Download Source: | !Download Source: | ||
| ftp://ftp.alsa-project.org/pub/tools/alsa-tools-{{ALSA Tools-Version}}.tar.bz2 | | ftp://ftp.alsa-project.org/pub/tools/alsa-tools-{{ALSA Tools-Version}}.tar.bz2 | ||
| − | |||
| − | |||
| − | |||
|} | |} | ||
| Line 26: | Line 23: | ||
== Non-Multilib == | == Non-Multilib == | ||
| − | |||
| − | |||
| − | |||
| − | |||
Compile each package with: | Compile each package with: | ||
| Line 43: | Line 36: | ||
=== 32Bit === | === 32Bit === | ||
| − | |||
| − | |||
| − | |||
| − | |||
Compile each package with: | Compile each package with: | ||
| Line 59: | Line 48: | ||
=== N32 === | === N32 === | ||
| − | |||
| − | |||
| − | |||
| − | |||
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: | Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: | ||
| Line 79: | Line 64: | ||
=== 64Bit === | === 64Bit === | ||
| − | |||
| − | |||
| − | |||
| − | |||
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: | Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries: | ||
Latest revision as of 10:03, 16 October 2007
| Download Source: | ftp://ftp.alsa-project.org/pub/tools/alsa-tools-1.0.23.tar.bz2 |
|---|
Contents
Introduction to ALSA Tools
The ALSA Tools package contains various advanced tools for use with certain sound cards.
This package is only needed if you have advanced requirements for your sound card. A list of the various tools can be found at http://alsa.opensrc.org/Alsa-tools.
Project Homepage: http://www.alsa-project.org/
Note
You don't compile the tools all at once, but instead build them individually. For each tool that you wish to build, you go into its directory and run the build commands from there.
Dependencies
Required
Optional
- Gtk1 (To Build echomixer, envy24control, and rmedigicontrol)
- FLTK (To Build hdspconf and hdspmixer)
- Qt3 (To Build qlo10k1)
Note
ld10k1 must be built before qt10k1
Non-Multilib
Compile each package with:
./configure --prefix=/usr && make
Install each package with:
make install
Multilib
32Bit
Compile each package with:
CC="gcc ${BUILD32}" CXX="g++ ${BUILD32}" USE_ARCH=32 PKG_CONFIG_PATH="${PKG_CONFIG_PATH32}" \
./configure --prefix=/usr &&
make
Install each package with:
make install
N32
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries:
sed -i "s@QTDIR/lib@&32@g" configure
Compile each package with:
CC="gcc ${BUILDN32}" CXX="g++ ${BUILDN32}" USE_ARCH=n32 PKG_CONFIG_PATH="${PKG_CONFIG_PATHN32}" \
./configure --prefix=/usr --libdir=/usr/lib32 &&
make
Install each package with:
make install
64Bit
Before building qlo10k1 apply the following sed so it looks in the correct dir for libraries:
sed -i "s@QTDIR/lib@&64@g" configure
Compile each package with:
CC="gcc ${BUILD64}" CXX="g++ ${BUILD64}" USE_ARCH=64 PKG_CONFIG_PATH="${PKG_CONFIG_PATH64}" \
./configure --prefix=/usr --libdir=/usr/lib64 &&
make
Install each package with:
make install
