Difference between revisions of "Gnome Pre-Installation Configuration"
(→Installing Gnome into /opt) |
(→Installing Gnome into /opt) |
||
| Line 41: | Line 41: | ||
export GNOME_PREFIX=/opt/gnome-2.6.16 | export GNOME_PREFIX=/opt/gnome-2.6.16 | ||
| + | export LIBGLADE_EXE_PREFIX=/opt/gnome | ||
export PATH="${PATH}:/opt/gnome/bin" | export PATH="${PATH}:/opt/gnome/bin" | ||
Revision as of 16:33, 28 October 2006
If you're using the Bash Startup Files then run the commands below. Otherwise make sure that the values you want are properly set.
Contents
Installation Strategies
If you're committed to Gnome as your desktop, you will likely install it in the /usr hierarchy. If less committed, or you prefer to install Gnome in an easy to remove location, the /opt hierarchy may be more suitable.
Installing Gnome into /usr
Create and addition to the Bash Startup Files:
cat > /etc/profile.d/30-gnome.sh << "EOF"
# Begin /etc/profile.d/30-gnome.sh
export GNOME_PREFIX=/usr
export XDG_CONFIG_DIRS="${XDG_CONFIG_DIRS}${XDG_CONFIG_DIRS+:}/etc/gnome/xdg"
# End /etc/profile.d/30-gnome.sh
EOF
source /etc/profile
Installing Gnome into /opt
Create a link from gnome-2.6.16 to gnome to make upgrades and changes in the future easier:
install -dv -m755 /opt/gnome-2.6.16 && ln -sf gnome-2.6.16 /opt/gnome
Even though the env variables are refering to /opt/gnome, GNOME_PREFIX should still be set to /opt/gnome-2.6.16 as that's where Gnome is going to be installed to.
Gnome heavily relies on DBUS. GNOME Virtual File System and Control Center (These are not all of the packages that do) both install a dbus service file that will end up outside of where DBUS will look for the services. Use the following sed to make DBUS look in /opt/gnome.
sed -i "/<servicedir>\/usr\/share/a\ <servicedir>/opt/gnome/share/dbus-1/services</servicedir>" /etc/dbus-1/session.conf
Non-Multilib
Create an addition to the Bash Startup Files:
cat > /etc/profile.d/30-gnome.sh << "EOF"
# Begin /etc/profile.d/30-gnome.sh
export GNOME_PREFIX=/opt/gnome-2.6.16
export LIBGLADE_EXE_PREFIX=/opt/gnome
export PATH="${PATH}:/opt/gnome/bin"
export PKG_CONFIG_PATH="${PKG_CONFIG_PATH}${PKG_CONFIG_PATH+:}/opt/gnome/lib/pkgconfig"
export XDG_DATA_DIRS="${XDG_DATA_DIRS}${XDG_DATA_DIRS+:}/opt/gnome/share"
export XDG_CONFIG_DIRS="${XDG_CONFIG_DIRS}${XDG_CONFIG_DIRS+:}/etc/gnome/xdg"
# End /etc/profile.d/30-gnome.sh
EOF
source /etc/profile
Add a new entry to /etc/ld.so.conf for the libraries that Gnome is going to install:
cat >> /etc/ld.so.conf << "EOF" # Begin Gnome addition to /etc/ld.so.conf /opt/gnome/lib # End Gnome addition EOF
Multilib
Create an addition to the Bash Startup Files:
cat > /etc/profile.d/30-gnome.sh << "EOF"
# Begin /etc/profile.d/30-gnome.sh
export GNOME_PREFIX=/opt/gnome-2.6.16
export PATH="${PATH}:/opt/gnome/bin"
export PKG_CONFIG_PATH32="${PKG_CONFIG_PATH32}${PKG_CONFIG_PATH32+:}/opt/gnome/lib/pkgconfig"
export PKG_CONFIG_PATHN32="${PKG_CONFIG_PATHN32}${PKG_CONFIG_PATHN32+:}/opt/gnome/lib32/pkgconfig"
export PKG_CONFIG_PATH64="${PKG_CONFIG_PATH64}${PKG_CONFIG_PATH64+:}/opt/gnome/lib64/pkgconfig"
export XDG_DATA_DIRS="${XDG_DATA_DIRS}${XDG_DATA_DIRS+:}/opt/gnome/share"
export XDG_CONFIG_DIRS="${XDG_CONFIG_DIRS}${XDG_CONFIG_DIRS+:}/etc/gnome/xdg"
# End /etc/profile.d/30-gnome.sh
EOF
source /etc/profile
Add a new entry to /etc/ld.so.conf for the libraries that Gnome is going to install:
cat >> /etc/ld.so.conf << "EOF" # Begin Gnome addition to /etc/ld.so.conf /opt/gnome/lib /opt/gnome/lib32 /opt/gnome/lib64 # End Gnome addition EOF
